Linha de produção Kartro
Se decidir comprar equipamento a baixo preço, certifique-se de que contacta com o verdadeiro vendedor. Obtenha todas as informações possíveis sobre o proprietário do equipamento. Uma das formas de enganar potenciais clientes consiste em apresentarem-se como uma empresa real. Caso tenha suspeitas, informe-nos sobre as mesmas, para que possamos proceder a controlos adicionais, através do formulário destinado a transmitir comentários e opiniões.
Antes de efetuar uma compra, analise atentamente vários ofertas, para ter uma ideia do preço médio de venda do equipamento que escolheu. Se o preço da oferta que mais lhe agrada for muito inferior ao de outras ofertas idênticas, desconfie. Uma diferença de preço significativa pode indicar defeitos ocultos no equipamento ou uma tentativa de cometer atos fraudulentos por parte do vendedor.
Não compre produtos cujo preço se afaste marcadamente do preço médio de produtos similares.
Não efetue pagamentos por conta nem adquira produtos pré-pagos duvidosos. Em caso de dúvida, não receie pedir esclarecimentos e fotografias e documentação adicionais do equipamento, verificar a autenticidade de documentos e fazer perguntas.
É o tipo de fraude mais comum. Vendedores desonestos podem pedir um pagamento por conta ou sinal para assegurar a "reserva" do equipamento. Desta forma, os falsos vendedores podem conseguir um elevado montante e desaparecer, deixando de contactar os compradores e ficando incontactáveis.
- A realização do pagamento por conta com cartão
- Não efetue qualquer pagamento por conta sem documentos que confirmem a transferência do dinheiro, caso tenha dúvidas sobre o vendedor.
- A transferência do pagamento por conta para a conta do “administrador”
- Um pedido desta natureza deve alertá-lo, pois é muito provavelmente sinónimo de que está a negociar com um burlão.
- A transferência do pagamento por conta para a conta de uma empresa com o mesmo nome
- Seja cauteloso, os burlões podem utilizar nomes de empresas muito conhecidas, aos quais introduzem alterações quase impercetíveis. Se tiver a menor dúvida quanto ao nome da empresa, não efetue qualquer transferência.
- A substituição de dados na fatura de uma empresa real
- Antes de efetuar uma transferência, certifique-se de que os dados indicados estão corretos e que correspondem à empresa especificada.
+358 50 02...
Mostrar
+358 50 0264325
Eslováquia, Kežmarok
Alemanha, Dabergotz
Alemanha, Enger
Bélgica, Deinze
Bélgica, Deinze
Espanha
Espanha
Polónia, Location:łódź
Finlândia, Tampere
Eslováquia, Kežmarok
Alemanha, Location:dortmund
Uzbequistão, Tashkent
Uzbequistão, Tashkent
Uzbequistão, Tashkent
Uzbequistão, Tashkent
Uzbequistão, Tashkent
Polónia, Krotoszyn
Roménia, Bacău
Production line for floor and intermediate floor structures in wood, which has been in use for 10 years for modular house manufacturing / volume house manufacturing.
Production line for floor blocks:
Station 1: Fixing station for manufacturing the frame structure, gluing, and nailing of the deck.
The station is designed for floor blocks with dimensions of 12,500 x 4,300 mm and is not adjustable in width.
The station has 5 transverse C-rails with manually adjustable fixing stops for 8 beams.
The station is equipped with 5 transverse roller conveyors that are pneumatically adjustable in height for transport to station 2. The C-rails and roller conveyors are manually movable sideways.
Nailing portal for Station 1.
The nailing portal runs on a rack rail mounted on the station.
The portal should be equipped with 8 nail guns for longitudinal nailing (nail guns removed = not included). The nail guns are adjustable sideways (for different spacing).
For cross-nailing in the floor structure, the portal is equipped with a motorized carriage with 1 nail gun (nail gun removed = not included).
The portal is equipped with a glue unit (10 l tank) and 9 glue nozzles for automatic application of glue. The glue nozzles are mounted together with the respective nail guns. The portal applies glue in one direction and nails on the return after sheet application.
On the transverse nailing cart, a panel saw is mounted. The saw is pneumatically pivotable by 90 degrees.
The saw is cranked across the floor block in the transverse direction and locked in position for longitudinal cutting. The saw is equipped with protection and a connection for extraction (dust extraction not included).
On both sides of the station, there are two outlets for air and electricity for hand tools in the station's underframe.
The operator follows the portal, standing on a motorized platform, and during longitudinal nailing, signals are received from pre-set firing stops. When nailing short beams, the operator stops the portal and starts the nailing carriage for crosswise nailing. Manual nail firing is also possible.
Station 2: Workstation and first turning section.
Manual workstation.
The station is equipped with 5 transverse, non-driven roller conveyors. The conveyors are movable sideways.
Hydraulic tilting of the station for turning the block over to station 3. Two outlets for air and electricity for hand tools in the station's underframe.
Station 3: Workstation and second turning section.
Manual workstation.
Hydraulic tilting and reception of the block from station 2.
The station is equipped with 5 transverse, non-driven roller conveyors. The conveyors are movable sideways. On both sides of the station, there are two outlets for air and electricity for hand tools in the station's underframe.
The floor block is transported on the roller conveyors back to station 2 for insulation and other processes.
The station is mobile and movable by motor sideways approximately 5 m.
Production line for intermediate floor structures:
Station 1: Fixing station for manufacturing the frame structure.
The station is designed for element sizes of 12,500 mm x 4,300 mm and is not adjustable in width.
The table has pneumatic alignment and locking from one side.
The table has 2 longitudinal C-profiles with manually adjustable fixing angles for transverse floor beams.
Hydraulic tilting of the station for turning over to station 2. Manual placement and nailing of ceiling panels.
Station 2: Workstation and turning section.
The station has pneumatic alignment from one side.
Hydraulic tilting of the station for receiving the block.
The table is covered with a plywood sheet.
The station is mobile and movable approximately 5 m.
Nailing portal and transport cart for station 1.
The nailing portal runs on a rack rail mounted on the station.
On top of the portal, there is a non-driven roller conveyor for storing cross beams, from which operators take and place them in the fixing angles.
The portal is driven by a frequency-controlled electric motor, which the operator controls with a joystick. The operator can stand on a platform that follows during nailing.
The portal is equipped with 2 x 2 nail guns (nail guns removed = not included) in a horizontal position on each side of the portal for nailing the cross beams.
The nailing portal nails with a spacing determined by pre-set stops, with the possibility of manual firing.
Nailing portal for station 2.
The nailing portal is motorized and runs on a rack rail recessed in the floor.
The portal is equipped with 2 carriages, each with one nail gun (nail guns removed = not included), running transversely to the floor structure for nailing in the transverse beams.
The carriages are also equipped with glue nozzles with accessories for applying glue to the beams.
The glue nozzles are mounted together with the respective nail guns.
The portal is equipped with a transverse saw that is pneumatically pivotable by 90 degrees. The saw is equipped with protection and a connection for dust extraction (dust extraction not included).
The operator follows the portal during nailing/gluing and stops it at each beam. The portal is driven by a frequency-controlled electric motor, which the operator controls with a joystick. The operator can stand on a platform that follows during nailing.
The portal nails transversely with spacing determined by pre-set stops. Manual firing is possible. The cross-cut saw can be motor-driven across the block. The operator locks it in the desired position for longitudinal cutting. The nailing portal follows when the station moves sideways.